AOR WX2000 Instructions d'exploitation télécharger pdf (Page 10)

ENGLISH

ENG

• Restart protection: Prevents the machine from

starting unintentionally

• Carbon brushes

(The special product features listed depend on the

equipment)

Before plugging in, check to see that the

rated mains voltage and mains frequency, as

specified on the rating label, match your power

supply.

6.1 Attaching the additional handle

Always work with the additional handle

attached (5)! Manually screw in the additional

handle securely in the left, centre or right threaded

hole (depending on requirements).

6.2 Attaching the safety guard

(for work involving grinding wheels)

Prior to commissioning: Fit the

protective cover.

For reasons of safety, the safety guard (6)

should always be attached when roughing

work is performed.

For reasons of safety, the special parting

guard should always be attached before

parting work is performed (see chapter 11 Acces-

sories).

See illustration D/E on page 3.

- Slacken the screw (10). Place the safety guard (6)

in the position indicated.

- Turn the safety guard until the closed section is

facing the operator.

- Tighten the screw (10), ensuring that the anti-

twist device engages in the slots.

- Make sure that the guard is seated securely: you

should not be able to turn the safety guard.

6.3 Power supply

The mains sockets must be protected using time-

delay fuses or circuit breakers.

Machines with "X" in the model designation:

(with integrated, automatic restriction of the

starting current (soft start)). The mains sockets can

also be protected using fast-acting fuses or circuit

breakers.

Disconnect the mains plug before changing

any accessories. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting

guard before performing parting work (see

chapter 11 Accessories).

7.1 Locking the spindle

Press in the spindle locking button (2) only

when the spindle is stationary!

- Press in the spindle locking button (2) and turn

the spindle

(1) by hand until you feel the spindle locking

button engage.

7.2 Placing the grinding wheel in position

See illustration B on page 3.

- Fit the support flange (7) on the spindle. The

flange should not turn on the spindle when prop-

erly attached.

- Position the grinding wheel on the support flange

(7) as shown in illustration B.

The grinding wheel must lay flat on the

supporting flange. The metal flange on the

parting grinder disc must lay flat on the support

flange.

7.3 Securing/Releasing the clamping nut

Securing the clamping nut (8):

The 2 sides of the clamping nut are different.

Screw the clamping nut onto the spindle as

follows:

See illustration C on page 3.

A) For thin grinding wheels:

The edge of the clamping nut (8) faces upwards

so that the thin grinding wheel can be attached

securely.

B) For thick grinding wheels:

The edge of the clamping nut (8) faces down-

wards so that the clamping nut can be attached

securely to the spindle.

- Lock the spindle. Turn the clamping nut (8)

clockwise using the 2-hole spanner (9) to

secure.

Releasing the clamping nut:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (8) anticlockwise using the 2-hole

spanner (9) to unscrew.

6 Commissioning

7 Attaching the grinding

wheel

17026997_0710 W 2000 WX 2000 NAFTA.book Seite 10 Dienstag, 20. Juli 2010 2:23 14

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 39 40

Commentaires sur ces manuels

Pas de commentaire

AOR WX2000 Instructions d'exploitation Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteur AOR WX2000